No USB Serial port available.

[slaftos]

Hardware:

Board: MAGTAG29_ESP32S2
Core Installation version: idf-release/v4.2
IDE name: Arduino CLI or Arduino IDE 8.1.13
Flash Frequency: build.flash_freq=80m
PSRAM enabled: Same results enabled or disabled
Upload Speed: 921600
Computer OS: Mac OS Mohave 10.14.6/Windows 10

Description:

After upload and reset USB serial port is not identified/found by OS.
Tested on Both Windows and Mac OS
Happens on a simple blink sketch, Serial.begin is called first line in setup.
Cloned a fresh release today where this was happening. Commit prior to below did not have this problem:

ESP-IDF update to 2bfdd036b and ESP-DSP

 idf-release/v4.2 (#4485) 

Code operates correctly (blinks) but no USB Serial port available.
Booting up ROM bootloader serial port comes up just fine /dev/cu.usbmodem01

Sketch:

// the setup function runs once when you press reset or power the board
void setup() {

  // initialize USB serial converter so we have a port created
  Serial.begin();

  // initialize built in LED pin as an output.
  pinMode(LED_BUILTIN, OUTPUT);}

// the loop function runs over and over again forever
void loop() {
  digitalWrite(LED_BUILTIN, HIGH);   // turn the LED on (HIGH is the voltage level)
  delay(1000);              // wait for a second
  digitalWrite(LED_BUILTIN, LOW);    // turn the LED off by making the voltage LOW
  delay(1000);              // wait for a second
}

Debug Messages:

USB serial port not available

[SvenArke]

Syntax: Serial.begin(speed)

Serial.begin(9600);

Already tried ?

[slaftos]

Yes even with a speed set it has the same result. The USB device is just not recognized, not a communication issue. It is more like a USB handshake issue, since neither windows nor Macos can recognize the device. But switching back to the previous commit of idf-release/v4.2 and it works correctly.

[rdmcmurray]

I can confirm the issue. My Metro ESP32-S2 that will only appear as an available port when reset in boot loader mode. Just ran into this today with 4.2#4704

Board: Adafruit Metro ESP32-S2
Core Installation version: idf-release/v4.2
IDE name: Arduino CLI or Arduino IDE 8.1.13
Flash Frequency: build.flash_freq=80m
PSRAM enabled: Same results enabled or disabled
Upload Speed: 921600
Computer OS: Mac OS Big Sur

[dwriggles]

I am having this issue as well. Same board and config but with Mac OS Catalina.

[friggeri]

I am having the same issue as @rdmcmurray, same OS and configuration

[StarWitch]

Having the same issue with the UnexpectedMaker Feather S2 (ESP32-S2). Switching back to the stale esp32s2 branch fixes it.

[shlomozippel]

Finally figured this out. The bug is in IDF 4.2, not the arduino core. This is just a bandaid until espressif fix it for real

shlomozippel@593515c

The bug is on this line: https://github.com/espressif/esp-idf/blob/release/v4.2/components/tinyusb/port/esp32s2/src/tinyusb.c#L89

Although, I should note: this "fixes" the USB in the sense that you can flash and monitor serial over the built in USB peripheral. You can't really do anything else though since tinyusb uses hardcoded descriptors and ignores anything you do e.g USB.VID() etc.

[ssilverman]

This fix looks like it's in the latest master, but I still don't see a serial port over USB. Is there a new fix?

[stale]

[STALE_SET] This issue has been automatically marked as stale because it has not had recent activity. It will be closed in 14 days if no further activity occurs. Thank you for your contributions.

[ssilverman]

Is this fixed? Pinging to keep the issue alive.

[stale]

[STALE_CLR] This issue has been removed from the stale queue. Please ensure activity to keep it openin the future.